![]() Step 6) Recording the requested datalogs - Video Time Stamp 2:10 ![]() ![]() It is located on the top left of the screen. Once the vehicle is up to operating temperature, click the button that is shaped like an SCT device with a green circle on it. STEP 5) Starting the datalog recording - Video Time Stamp 1:46 Once communication is established, click the Load Config at the top in the Chart Gauges menu. STEP 4) Loading the configuration (.cf4) file - Video Time Stamp 1:33 Verify that you're using the USB cable that came with the SCT device. * If the device and vehicle do not communicate, disconnect all the cables and reconnect. Once on the Communications screen, click the Check Communication button. Start the vehicle's engine, and click the Comm button located in the Settings menu at the top of the screen. STEP 3) Checking Device Communications - Video Time Stamp 1:16 Plug the Micro USB cable into the laptop and the bottom of the SCT device, and the OBD2 cable into the OBD2 port and the top of the SCT device. STEP 2) Connecting the SCT device cables - Video Time Stamp 0:56 STEP 1) Downloading the SCT datalogging software and the VMP configuration (.cf4) file - Video Time Stamp 0:29 SCT Device Updater Software : Click HERE to download Device Updater SCT Livelink GENII Datalogging Software : Click HERE to download Livelink LIVELINK - STEP BY STEP DATALOGGING INSTRUCTIONS THROUGH A LAPTOP Please turn off the air conditioning and defrost before starting your recording. Please have gone through at least (2) consecutive tanks of one type of fuel before logging ![]() Language should be set to "English (United States)" Time Zone should be set to "Eastern Time (US & Canada)" Regional Format should be set to "English (United States)" Laptops must have the Time & Language settings set to certain configuration in order for us to be able to open / review datalogsĬountry/Region should be set to "United States" LAST NAME - FUEL BEING USED - TYPE OF LOG - D ATE - SCT DEVICE SERIAL NUMBER.CSVĮxample) Smith-93Octane-IdleSlowRev-01012020-X4111222333.CSV Please name your file with this naming convention: Preferred naming convention of datalog file VMP offe rs configuration files that will layout the needed parameters for many vehicle platforms. This is CRUCIAL when addressing concerns. The following is IMPORTANT when datalogging: Turn the car off, and allow the ECU to completely power down before starting the vehicle.ĭatalogging your vehicle allows your tuner to see ECU parameters in real time and make tuning adjustments accordingly.Ī good datalog will help your tuner address concerns and verify proper vehicle operation. **Your VMP custom tune will be displayed in your device with the following naming format: Fuel Octane VMP MM/DD/YYYY EXAMPLE: 93 VMP Ĭlick the right arrow on the device to highlight and select the "Approve" optionĬonfirm the information on the screen reflects the VMP tune, and select "Continue"Ĭontinue to follow the prompts on the screen until the screen displays "DOWNLOAD COMPLETE" ** It is important that you flash the VMP custom tune file and not the preloaded tunes that come in the SCT device. Navigate down to highlight and select the VMP Tune File Read and follow the prompts on the screen Select "PROGRAM VEHICLE" on the main menu of the SCT device Plug SCT device into the OBD2 port of the vehicle using the OBD2 cable provided You can load the tune file directly to your vehicle by: When you've purchased you r SCT device d irectly from VMP in the same order as your custom tune, your tune file may have been loaded to your SCT device before it had shipped out. If your VMP custom tune file(s) have already been loaded to your SCT device Wait for "Load complete" message before disconnecting SCT device from laptop You will see the name of the file appear under the "On Device" listĬlick "Program" to begin loading the file to your device You will see the name of the file appear under the "Available Tunes" list Navigate to the location where you've saved. Select "Load Custom Tune File" from the menu of the Device Updater Program.Ĭlick "Browse" from the top right corner of the program *Note, other cables can be used but they must be a data cable that is capable of transferring files - not just charging* CEF tune file from the email chain that you have with your calibratorĬonnect the SCT device to your computer using the provided Micro-USB to USB cable When you've purchased your S CT device separately from the VMP custom tune, the tune file will be sent to you via email and will need to be loaded to your SCT device before it can be loaded to your vehicle. If your VMP custom tune file(s) were sent to you via Email
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |